1. السلام علیکم
    آئی ٹی استاد ڈاٹ کام وزٹ کرنے کا شکریہ۔ ہم آپکو خوش آمدید کہتے ہیں۔ فورم کے کسی بھی حصے کو استعمال میں لانے جیسے پوسٹنگ کرنے، کوئی تھریڈ دیکھنے یا لکھنے کسی بھی ممبر سے رابطہ کرنے کے لئے اور فورم کے دیگر آلات وغیرہ کا استعمال کرنے کے لئے آپکا رجسٹر ہونا ضروری ہے۔ رجسٹر ہونے کے لئے یہاں کلک کریں۔ رجسٹریشن حاصل کرنا بالکل آسان اور بالکل مفت ہے۔

How To Install/Change Camera iPhone 3GS

Discussion in 'Mobile phones Hardware & SOftware Zone' started by ғσяυм gυяυ, Jun 26, 2013.

  1. 1st Step
    Remove the two Phillips #00 screws from the dock-connector end of the iPhone.

    Hello guest, Thank you for Register or you log to see the links!




    2nd Step
    Remove the metal handle from the suction cup. It's easier and safer to grip the suction cup's base instead of the metal handle.
    There is a rubber gasket between the silver front bezel and black display assembly. A bit of force is required in this step to separate the iPhone's display assembly.
    Be very careful when opening the iPhone so that the cables under the display are not severed.
    Use a small suction cup near the Home button to gently pull up the bottom portion of the iPhone's display assembly.
    If the display assembly is to damaged to allow the suction cup to adhere, tape with a strong adhesive such as duct tape maybe used.

    Hello guest, Thank you for Register or you log to see the links!



    3rd Step
    The display assembly is still connected to the iPhone by several cables, so don't try to remove it entirely just yet.
    Rotate the display assembly up until it is at an angle of approximately 45 degrees.

    Hello guest, Thank you for Register or you log to see the links!



    4th Step
    Continue to hold the display assembly with one hand, and use your other hand and a spudger to disconnect the black ribbon cable labeled "1."

    Hello guest, Thank you for Register or you log to see the links!



    5th Step
    Rotate the display assembly up until it is roughly vertical. This will allow easier access for disconnecting the remaining cables.
    Use a spudger to disconnect the black ribbon cable labeled "2."

    Hello guest, Thank you for Register or you log to see the links!



    6th Step
    Use a spudger to flip up the white plastic tab holding the remaining ribbon cable in place. The white tab will rotate up 90 degrees, releasing the ribbon cable.
    Slide the black ribbon cable out of its connector, and remove the display assembly from the iPhone.

    Hello guest, Thank you for Register or you log to see the links!



    7th Step
    Insert your SIM eject tool or a paper clip into the hole next to the headphone jack.
    Press down on the tool until the SIM card tray pops out.Grasp the SIM card tray and slide it out of the iPhone.

    Hello guest, Thank you for Register or you log to see the links!



    8th Step
    Use a spudger to disconnect the ribbon cable labeled "4."

    Hello guest, Thank you for Register or you log to see the links!




    9th Step
    Use a spudger to disconnect the ribbon cable labeled "5."


    Hello guest, Thank you for Register or you log to see the links!



    10th Step
    Use a spudger to disconnect the ribbon cable labeled "6."
    If you have an iPhone 3GS, refer to picture 2 and use a spudger to disconnect the ribbon cable labeled "7."

    Hello guest, Thank you for Register or you log to see the links!



    11th Step
    Carefully peel up the small sticker labeled "Do not remove."

    Hello guest, Thank you for Register or you log to see the links!



    12th Step
    Remove the following 8 screws:Five 2.3 mm Phillips #00 screws with partial threads securing the logic board to the rear panel.
    Two 2.3 mm Phillips #00 screws with full threads securing the logic board and camera.
    One 2.9 mm Phillips #00 screw from beneath the "Do not remove" sticker.

    Hello guest, Thank you for Register or you log to see the links!



    13th Step
    Use a spudger to gently pry the camera up and out of its housing in the rear panel. The camera cannot be removed entirely yet because it's connected to the bottom of the logic board.

    Hello guest, Thank you for Register or you log to see the links!



    14th Step

    Hello guest, Thank you for Register or you log to see the links!



    Use a spudger to gently pry up the end of the logic board closest to the dock connector.
    If the board won't lift up, double check to make sure all the screws securing the logic board have been removed.

    Hello guest, Thank you for Register or you log to see the links!



    15th Step
    Slide the logic board towards the dock connector and out of the iPhone.

    Hello guest, Thank you for Register or you log to see the links!



    16th Step
    Use a spudger to disconnect the camera from the logic board.​
     
  2. Ali

    Ali ITU Lover

    hmmmmmmm

    buat koob guru g


    umda sharing
     
  3. نائس ورک گرو برادر
    کیپ اِٹ اَپ
    :a030:
     
  4. Informatics Tips
    thumb Up ;)
     
  5. Hello guest, Thank you for Register or you log to see the links!

    hmmmmmmm

    buat koob guru g


    umda sharing
    Click to expand...
    Shukriya Visit Karnay Ka Aur Comments Karnay Ka ..
     
  • Hello guest, Thank you for Register or you log to see the links!

    نائس ورک گرو برادر
    کیپ اِٹ اَپ
    :a030:
    Click to expand...
    Shukriya Visit Karnay Ka Aur Comments Karnay Ka ..
     
  • Hello guest, Thank you for Register or you log to see the links!

    Informatics Tips
    thumb Up ;)
    Click to expand...
    Shukriya Visit Karnay Ka Aur Comments Karnay Ka ..
     
  • Hello guest, Thank you for Register or you log to see the links!

    Informatics Tips
    thumb Up ;)
    Click to expand...
    Shukriya Visit Karnay Aur Comments Denay Ka ...
     
  • very good guru sir
     
  • Hello guest, Thank you for Register or you log to see the links!

    very good guru sir
    Click to expand...
    SHukriya Visit Karnay Aur Comments Denay Ka ..
     
  • Share This Page